Skip to content
Alpha Insulation — Stay cooler. Save more.

Blown-in attic insulation specialists

Blown-In Attic Insulation for South Florida Homes

Alpha Insulation does one thing: blown-in, loose-fill attic insulation. We bring Florida attics up to an even, recommended depth so less heat reaches your living space — in Broward, Miami-Dade and Palm Beach counties, and north to Orlando and Kissimmee.

  • Blown-in only — no spray foam
  • Florida climate-zone targets
  • Depth measured & documented
  • Based in Hallandale Beach
Attic heatLoose-fill layerCooler rooms

What is blown-in insulation?

A thick, even blanket on your attic floor

Blown-in insulation is loose-fill material — usually fiberglass or cellulose — that’s blown through a hose and spread across the attic floor. It settles around everything up there, creating continuous coverage that slows heat moving from a hot attic into the rooms below.

In Florida, the attic is where the sun’s heat builds up. The attic floor is the barrier between that heat and your ceilings — and in many homes it’s thinner than today’s recommendations.

Complete coverage

Loose fill settles around joists, wiring and framing, closing the gaps that batts and thin old layers leave behind.

Cooler rooms under the attic

A deeper, even layer slows heat moving from a hot Florida attic into the rooms you are paying to cool.

Less work for your A/C

When less heat comes through the ceiling, your air conditioner has less heat to remove. Results vary by home.

Adds over what you have

If existing insulation is dry and sound, new loose fill can go right on top to reach the target R-value.

Fast, low-disruption install

Most attics are done in one visit, with the crew working from the attic access — not through your living space.

Measurable results

Loose-fill R-value is set by depth, so the finished job can be checked with a ruler against the bag’s coverage chart.

Why homeowners choose Alpha

Specialists in one job, done properly

Blown-in is all we do

We don’t sell spray foam or batts. Every recommendation is about one thing: whether loose-fill on your attic floor is right for your home.

Florida-specific targets

South Florida and the Orlando area have different code minimums (R-30 vs R-38). We size the job to your climate zone, not a national average.

Straight answers

If your attic has a roof leak, pest problem or wiring concern that should be fixed first, we tell you instead of insulating over it.

You see what you paid for

We install to the depth on the manufacturer’s coverage chart and walk you through the finished attic and the R-value installed.

Local and reachable

Our office is in Hallandale Beach, and a real person answers 754-227-1227.

Clean, respectful crews

We protect the path to your attic access and leave the work area as we found it.

How it works

Our installation process

  1. 01

    Request an estimate

    Call or send the form. Tell us your home’s size, location and what you’ve noticed.

  2. 02

    Attic inspection

    We measure existing depth, check coverage, ventilation, access and any red flags.

  3. 03

    Clear recommendation

    You get a target R-value, installed depth, material and price — with no pressure.

  4. 04

    Installation day

    We prep, keep soffit vents clear, blow in an even layer and review the finished attic with you.

Check your attic

Signs your home needs more attic insulation

  • You can see the tops of the ceiling joists in your attic
  • Bedrooms or rooms under the attic stay hot in the afternoon
  • Insulation looks thin, patchy, flattened or pushed aside
  • Your A/C seems to run almost constantly in summer
  • Your home was built before current energy codes
  • Recent A/C, electrical or roof work disturbed the attic
Read the full checklist
Measurethe depth

Florida heat & energy efficiency

How much attic insulation does a Florida home need?

Florida’s energy code splits the state into two climate zones. South Florida — including Miami-Dade, Broward and Palm Beach counties — is Climate Zone 1. Central Florida, including Orlando and Kissimmee, is Climate Zone 2, with a higher ceiling insulation minimum.

Those code minimums apply to new construction. Many existing homes were built to older standards, and their insulation has thinned or been disturbed since. Bringing an existing attic up to these levels is the most common reason homeowners call us.

The 9th Edition (2026) Florida Building Code takes effect December 31, 2026. We’ll update these figures if requirements change.

Attic insulation targets by Florida climate zone
RegionFBC new-home minimum (ceiling)ENERGY STAR — uninsulated attic
South Florida
Climate Zone 1
R-30R-30
Orlando / Kissimmee
Climate Zone 2
R-38R-49

Sources: 8th Edition (2023) Florida Building Code – Energy Conservation; ENERGY STAR recommended home insulation R-values.

Service area

South Florida, and north to Orlando

Our office is in Hallandale Beach. We cover all three South Florida counties and extend our service to the Orlando and Kissimmee area.

Central Florida

No Central Florida office — call to confirm scheduling for your address.

FAQ

Common questions

Straight answers about blown-in insulation in Florida.

All FAQs

What is blown-in insulation?

Blown-in insulation, also called loose-fill insulation, is made of small fibers or particles — usually fiberglass or cellulose — that are blown through a hose by a machine and spread across the attic floor. It forms a continuous blanket that fills around joists, wiring and other obstructions.

What R-value should Florida homeowners have?

Under the 8th Edition (2023) Florida Building Code, the prescriptive ceiling insulation minimum for new homes is R-30 in Climate Zone 1 (including Miami-Dade, Broward and Palm Beach counties) and R-38 in Climate Zone 2 (including Orlando and Kissimmee). ENERGY STAR’s retrofit guidance recommends R-30 for an uninsulated Zone 1 attic and R-49 for an uninsulated Zone 2 attic.

Can blown-in insulation lower electric bills?

It can reduce the amount of heat entering your home through the ceiling, which can reduce how much your air conditioner has to run. The actual effect depends on your existing insulation, air leaks, ductwork, A/C equipment and thermostat habits, so we do not guarantee specific savings.

How much does blown-in insulation cost in Florida?

Cost depends mainly on the size of the attic, how much insulation is already there, the target R-value, how accessible the attic is, and whether any preparation or removal is needed. Because those factors vary so much from home to home, we give pricing after seeing the attic rather than quoting a flat rate.

Can new insulation be installed over existing insulation?

Usually, yes. If the existing insulation is dry and not contaminated by mold or pests, new loose-fill can be blown on top to reach the target R-value. Compromised insulation should be addressed first.

Do you service Orlando and Kissimmee?

Yes. Our service area extends to the Orlando and Kissimmee area. We do not have an office there, so please call or request an estimate to confirm scheduling for your address.

Learn

Recent articles

View all articles

Cost & Value

How Much Does Blown-In Insulation Cost in Florida?

What determines the cost of blown-in attic insulation in Florida — attic size, existing insulation, target R-value, access and prep — and how to compare estimates fairly.

· 3 min read

Find out what your attic actually needs

Tell us about your home and we’ll check your existing insulation depth, coverage and attic conditions, then explain what blown-in insulation would — and wouldn’t — do for you.

Call NowGet Estimate