Skip to content
Alpha Insulation — Stay cooler. Save more.

Frequently asked questions

Blown-In Insulation FAQ

Clear, direct answers to the questions Florida homeowners ask most about blown-in attic insulation.

Blown-in insulation basics

What is blown-in insulation?

Blown-in insulation, also called loose-fill insulation, is made of small fibers or particles — usually fiberglass or cellulose — that are blown through a hose by a machine and spread across the attic floor. It forms a continuous blanket that fills around joists, wiring and other obstructions.

How does blown-in insulation work?

The loose fibers trap pockets of air, which slows the transfer of heat. In Florida, that means less of the heat from a hot attic moves down through the ceiling into your living space. How well it works depends on the installed depth, which determines the R-value.

How long does blown-in insulation last?

Kept dry and undisturbed, loose-fill insulation can last for decades. It loses effectiveness when it gets wet, compressed, contaminated by pests, or pushed aside during other attic work, which is why an inspection matters more than the age alone.

Can new insulation be installed over existing insulation?

Usually, yes. If the existing insulation is dry and not contaminated by mold or pests, new loose-fill can be blown on top to reach the target R-value. Compromised insulation should be addressed first.

Is blown-in insulation suitable for older homes?

Generally, yes. Older homes often have flat ceilings under ventilated attics, which is where blown-in insulation works best. Older homes also warrant a careful inspection for things like outdated wiring, roof leaks or old insulation types that should be handled before new insulation goes in.

Do you install spray foam insulation?

No. Alpha Insulation specializes exclusively in blown-in, loose-fill attic insulation. We do not offer spray foam or batt installation.

R-value and how much you need

What R-value should Florida homeowners have?

Under the 8th Edition (2023) Florida Building Code, the prescriptive ceiling insulation minimum for new homes is R-30 in Climate Zone 1 (including Miami-Dade, Broward and Palm Beach counties) and R-38 in Climate Zone 2 (including Orlando and Kissimmee). ENERGY STAR’s retrofit guidance recommends R-30 for an uninsulated Zone 1 attic and R-49 for an uninsulated Zone 2 attic.

How much insulation does my attic need?

Enough to reach your target R-value at a consistent depth across the whole attic floor. The exact depth depends on the product: each loose-fill bag lists the minimum thickness required for each R-value. As a rough guide, ENERGY STAR estimates about R-3 per inch, so R-30 is roughly 10 inches or more depending on the material.

How do I know if my attic needs more insulation?

Look across the attic: if the insulation is level with or below the tops of the ceiling joists, you probably need more. Other signs include rooms under the attic that run hot, bare or thin spots, and insulation that has been flattened or pushed aside.

Comfort, energy and humidity

Can blown-in insulation lower electric bills?

It can reduce the amount of heat entering your home through the ceiling, which can reduce how much your air conditioner has to run. The actual effect depends on your existing insulation, air leaks, ductwork, A/C equipment and thermostat habits, so we do not guarantee specific savings.

Does insulation help keep a home cooler?

Yes. Attic insulation slows heat moving from a hot attic into the rooms below. Homes with thin or uneven attic insulation often have rooms that stay warm in the afternoon even with the A/C running; bringing the attic to a consistent depth helps even that out.

Does insulation help with humidity?

Insulation is not a dehumidifier and does not fix moisture problems. By reducing heat gain, it can help your A/C run in steadier cycles, and properly sized A/C systems remove moisture while they run. Roof leaks, poor ventilation or condensation problems need to be fixed separately — and before insulating.

Cost and installation

How much does blown-in insulation cost in Florida?

Cost depends mainly on the size of the attic, how much insulation is already there, the target R-value, how accessible the attic is, and whether any preparation or removal is needed. Because those factors vary so much from home to home, we give pricing after seeing the attic rather than quoting a flat rate.

How long does installation take?

Most single-family attics are completed in a single visit, frequently within a few hours. Large or hard-to-reach attics can take longer. Your estimate will include an expected timeline.

What happens during an insulation installation?

The crew protects the path to the attic access, checks the attic, keeps soffit vents and non-rated light fixtures clear, then blows loose-fill insulation evenly across the attic floor to the target depth. When finished, they review the work and the installed depth with you.

Service area

Do you service Miami-Dade, Broward, and Palm Beach?

Yes. We serve all three South Florida counties — Broward, Miami-Dade and Palm Beach — from our office in Hallandale Beach.

Do you service Orlando and Kissimmee?

Yes. Our service area extends to the Orlando and Kissimmee area. We do not have an office there, so please call or request an estimate to confirm scheduling for your address.

Still have a question?

Call us or send a note with your question. We’ll give you a straight answer — even if the answer is that your attic doesn’t need more insulation.

Call NowGet Estimate